img

新闻中心

NEWS

新闻中心

News Center

新闻中心
/
/
/
Detailed explanation of three common drilling holes in PCB

Detailed explanation of three common drilling holes in PCB

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2020-09-11 17:26
  • Views:

(Summary description)Common drilling holes in PCB: through holes, blind holes, buried holes. The meaning and characteristics of these three kinds of holes.

Detailed explanation of three common drilling holes in PCB

(Summary description)Common drilling holes in PCB: through holes, blind holes, buried holes. The meaning and characteristics of these three kinds of holes.

  • Categories:Company News
  • Author:
  • Origin:
  • Time of issue:2020-09-11 17:26
  • Views:
Information
Common drilling holes in PCB: through holes, blind holes, buried holes. The meaning and characteristics of these three kinds of holes.
 
Via (VIA), this is a common hole used to conduct or connect copper foil lines between conductive patterns in different layers of the circuit board. For example (such as blind holes, buried holes), but can not insert component leads or copper-plated holes of other reinforced materials. Because the PCB is formed by the accumulation of many copper foil layers, each layer of copper foil will be covered with an insulating layer, so that the copper foil layers cannot communicate with each other, and the signal link depends on the via hole (Via), so there is the title of Chinese via.
 
The characteristic is: in order to meet the needs of customers, the through holes of the circuit board must be plugged. In this way, in changing the traditional aluminum plug hole process, the circuit board surface solder mask and plug hole are completed with white mesh to make the production stable. The quality is reliable and the application is more perfect. Vias mainly play the role of interconnection and conduction of circuits. With the rapid development of the electronics industry, higher requirements are also placed on the process and surface mount technology of printed circuit boards. The process of plugging the via hole is applied, and the following requirements should be met at the same time: 1. There is copper in the via hole, and the solder mask can be plugged or not. 2. There must be tin and lead in the through hole, and there is a certain thickness requirement (4um) that no solder mask ink can enter the hole, resulting in hidden tin beads in the hole. 3. The through hole must have a solder mask plug hole, opaque, and must not have tin rings, tin beads, and flatness requirements.
 
Blind hole: It is to connect the outermost circuit in the PCB with the adjacent inner layer by plating holes. Because the opposite side cannot be seen, it is called blind through. At the same time, in order to increase the space utilization between PCB circuit layers, blind vias are used. That is, a via hole to one surface of the printed board.
 
Features: Blind holes are located on the top and bottom surfaces of the circuit board with a certain depth. They are used to link the surface line and the inner line below. The depth of the hole usually does not exceed a certain ratio (aperture). This production method requires special attention to the depth of the drilling (Z-axis) to be just right. If you don’t pay attention, it will cause difficulties in electroplating in the hole, so almost no factory adopts it. You can also put the circuit layers that need to be connected in advance in the individual circuit layers. The holes are drilled first, and then glued together. However, more precise positioning and alignment devices are required.
 
Buried vias are the links between any circuit layers inside the PCB but are not connected to the outer layer, and also mean via holes that do not extend to the surface of the circuit board.
 
Features: This process cannot be achieved by drilling after bonding. It is necessary to perform drilling on individual circuit layers. First, the inner layer is partially bonded and then electroplated first. Finally, it can be fully bonded, which is more conductive than the original. Holes and blind holes take more time, so the price is the most expensive. This process is usually only used for high-density circuit boards to increase the usable space of other circuit layers. In the PCB production process, drilling is very important and should not be careless. Because drilling is to drill the required through holes on the copper clad board to provide electrical connections and fix the function of the device. If the operation is improper, there will be problems in the process of via holes, and the device cannot be fixed on the circuit board, which will affect the use, and the whole board will be scrapped, so the drilling process is very important.

Scan the QR code to read on your phone

Shenzhen Fullbest Technology Co. Ltd.
Shenzhen Fullbest Technology Co. Ltd.

Follow us

CopyRight @ 2020  Shenzhen Fullbest Technology Co. Ltd.